Starting from September of 2024, OPF-G, DPP will come with the M3 0.5 x 6mm plate to slide screws, but will no longer come with the M4 0..7 x 15.8mm DPP sight to plate screws, they will be optional (we'll offer them at our cost.) Delta Point Pro already comes with sight to plate screws, inclusion of these screws is unnecessary.
Do not use OPF-G, DPP with Holoson SCS320, it will damage the plate. OPF-G, DPP is not compatible with SIG Romeo X Pro (lug holes are too shallow on the X Pro).
GLOCKOPF-G, DPP is compatible with GLOCKs that use GLOCK's Set 01 plates (17, 19, 20, 21, 22, 23, 26, 34, 40, 45, 47, 49). G40 (10mm) uses Set 02 plates that are slightly wider, while OPF-G, DPP still works with it, it will not completely fill the MOS cut's width.
OPF-G, DPP is compatible with the EOTech EFLX, but the DPP sight screws to plates are longer, if you are buying OPF-G, DPP for use with EFLX, be sure to use the screws that came with your EFLX sight. DO NOT use DPP sight to plate screws with EFLX.
OPF-G, DPP (Optics Platform, Forward Controls, Delta Point Pro) is the latest member of the OPF line. OPF-G, DPP uses the same proven design of the OPF-G, RMR to keep the Delta Point Pro immobile, the simplest and most effective way to prevent sight to plate mounting screws from loosening and shearing.
While Leupold's Delta Point Pro uses 4 recoil lugs (twice as that of the RMR's) and beefier mounting screws, the challenges of keeping the sight on the plate without loosening or shearing the sight to plate screws are not very different from those of the RMR. OPF-G, DPP has a front and rear fence, the tight tolerances of the plate to slide, and sight to plate insures minimum movement along the bore in recoil.
OPF-G, DPP ships with 2 plate to slide screws (M3 0.5mm x 6mm), 2 Delta Point Pro screws M4 .7x15.8mm (from September 2024, sight to plate screws will be optional as they already come with the DPP) and a packet of VC3 Vibra-tite. A torque wrench is necessary to properly install both the plate to slide, and sight to plate screws.
Torque value:
Plate to slide: 13in/lb
Sight to plate: 25in/lb
Billet machined in 4140, hat treated and black nitride coated.
OPF-G, DPP is a collaboration between Tangodown and FCD. Proudly designed and made in the USA.
NOTE:
OPF-G, EFLX is compatible with the Leupold's Delta Point Pro. If the plate engraving says DPP only, it is the same plate we use for both DPP and EFLX.DPP sight to plates are longer, while EFLX uses shorter screws.
If you attempt to torque the DPP screws in with an EFLX installed, you can bend or break the plate. Do not use DPP sight to plate screws if you have and EFLX.
WARNING: This product can expose you to chemicals
including metallic nickel, chromium and lead, which are known to the
State of California to cause cancer or other reproductive harm. For more
information go to www.P65Warnings.ca.gov.
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither Forward Controls Design nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, components or accessories.
For additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and parts visit www.glock.com.
[ITEMPRICE]